| Model |
RG-AP840-I |
| Hardware specifications |
| Radio |
Dual-radio dual-band: Radio 1: 2.4G 11n: 2×2 MIMO Radio 2: 5G 11ax: 4x4 MIMO |
| Protocol |
Supports standard 802.11ax, dual-radio dual-band, concurrent 802.11ax and 802.11a/b/g/n/ac |
| Operating Bands |
802.11b/g/n :2.4G ~ 2.483GHz 802.11a/n/ac/ax : 5.150~5.350GHz,5.47~5.725GHz,5.725~5.850GHz (vary depending on different countries) |
| Spatial Streams |
Up to 6: 2×2:2 in 2.4GHz , 4×4:4 in 5GHz |
| Max Throughput |
Maximum throughput of 2.4G: 400Mbps Maximum throughput of 5G: 4.8Gbps Maximum throughput per AP: 5.2Gbps |
| Modulation |
OFDM:BPSK@6/9Mbps,QPSK@12/18Mbps,16-QAM@24Mbps,64-QAM@48/54Mbps DSSS:DBPSK@1Mbps,DQPSK@2Mbps,and CCK@5.5/11Mbps MIMO-OFDM:BPSK, QPSK, 16QAM, 64QAM, 256QAM and 1024QAM OFDMA (up to 1024-QAM) |
| Receiver Sensitivity |
11b:-96dBm(1Mbps),-93dBm(5Mbps),-89dBm(11Mbps) 11a/g:-91dBm(6Mbps),-85dBm(24Mbps),-80dBm(36Mbps),-74dBm(54Mbps) 11n:-90dBm(MCS0),-70dBm(MCS7),-89dBm(MCS8),-68dBm(MCS15) 11ac HT20:-88dBm(MCS0), -63dBm(MCS9) 11ac HT40:-85dBm(MCS0), -60dBm(MCS9) 11ac HT80:-82dBm(MCS0), -57dBm(MCS9) 11ax HT80:-82dBm(MCS0), -57dBm(MCS9), -52dBm(MCS11) 11ax HT160:-80dBm(MCS0), -49dBm(MCS11) |
| Antenna |
Integrated antenna design |
| Antenna Gain |
2.4G: 3dBi 5G: 3dBi |
| Service Ports |
3 10/100/1000M Ethernet ports (The LAN1 Port supports PoE in, LAN3 Port supports LAN & IoT module expansion with PoE out) |
| Management Port |
1 console port |
| USB |
1 USB 2.0 port |
| IoT Capability |
BLE |
| Reset Button |
Support |
| Anti-theft Lock |
Support |
| LED Indicator |
1 LED indicator (Supports red, green, blue, orange and flashing mode, which indicates device access. The indicator can be switched off to silent mode.) |
| Transmit Power |
≤100mw(20dBm) (vary depending on different countries) |
| Adjustable Power |
1dBm |
| Power Supply |
Local power supply (DC 48V/1A) (DC Power adapters should be purchased from third-party vendors separately if needed.) PoE+ (802.3at) PoE (802.3af) – Not recommended: 5G radio is degraded to 2x2 MIMO, and the PoE out of the LAN3/ IoT port is disabled |
| Power Consumption |
<25.4W |
| Physical Specifications |
| Temperature |
Operating Temperature: -10°C to 50°C |
| Storage Temperature: -40°C to 70°C |
| Humidity |
Operating Humidity: 5% to 95% (non-condensing) |
| Storage Humidity: 5% to 95% (non-condensing) |
| Installation Mode |
Ceiling/wall-mountable |
| Dimensions (W x D x H) |
220mm ×220mm x48.85mm(Height of the AP only, excluding the mount kit) |
| Weight |
1.30kg |
| MTBF |
250,000 hours |
| Certifications and Compliance |
| Safety Standard |
GB4943, EN/IEC 60950-1 |
| EMC Standard |
GB9254, EN301 489 EN 55032 , EN 61000, EN 55035 |
| Health Standard |
EN 62311 |
| Radio Standard |
SRRC, EN300 328, EN301 893 |
| Software Specifications |
| WLAN |
Maximum clients per AP |
1024 (Recommended Clients: 64) |
| BSSID capacity |
Up to 32 |
| SSID hiding |
Support |
| 5G Priority (Band Steering) |
Support |
| Configuring the authentication mode, encryption mechanism and VLAN attributes for each SSID |
Support |
| Remote Intelligent Perception Technology (RIPT) |
Support |
| Intelligent device recognition technology |
Support |
| Intelligent load balancing based on the number of users or traffic |
Support |
| STA control |
SSID/radio-based |
| Bandwidth control |
STA/SSID/AP-based bandwidth control |
| Data encryption |
WPA(TKIP), WPA-PSK, WPA2(AES), WPA3, WEP(64/128 bits) |
| PSK and web authentication |
Support |
| PPSK authentication (For Employee) |
Support (require wireless controller) |
| 802.1x authentication |
Support |
| PEAP authentication |
Support |
| Data frame filtering |
Whitelist, static/dynamic blacklist |
| User isolation |
Support |
| Rogue AP detection and countermeasure |
Support |
| Dynamic ACL assignment |
Support |
| RADIUS |
Support |
| CPU Protection Policy (CPP) |
Support |
| Network Foundation Protection Policy (NFPP) |
Support |
| IP |
IPv4 and IPv6 address |
Support |
| Multicast routing |
Multicast to unicast conversion |
| DHCP service |
DHCP Snooping, Option 82, Server, Client |
| Management and Maintenance |
Supported wireless LAN controllers |
Ruijie WS Series Wireless Controller Ruijie MACC-Base Software Controller Ruijie Cloud (Public Cloud) |
| Management protocol |
Telnet, SSH, TFTP, Web |
| Wireless Intelligent AI Optimization Service (WIS) |
Support |
| SNMP |
SNMPV1,V2c,V3 |
| Syslog / Debug |
Support |
| FAT/FIT/MACC mode switching |
Factory default firmware supports FAT (standalone) or FIT mode (WS controller) or MACC mode (Ruijie MACC-Base or Ruijie Cloud) management |